Intel Socket 478 AIMB-744 Manual de usuario

AIMB-744Socket 478 Intel® Pentium® 4/Celeron® Industrial ATX Motherboard with PCI-X/DDR/AGP/Dual GbE/800 MHz FSBUser’s Manual

AIMB-744 User’s Manual x3.6.14 Onboard Serial Port 2 ... 423.6.15 UART Mode Select ...

AIMB-744 User’s Manual 86B.14 ATX Soft Power Switch (CN21)Table B.14: ATX soft power switch (CN21)Pin Signal15VSB2PWR-BTN1

87 Appendix B B.15 H/W Monitor Alarm (CN22)B.16 SM Bus Connector (CN29)B.17 USB/LAN ports (CN31 and CN32)Table B.15: H/W monitor alarm (CN22)Pin S

AIMB-744 User’s Manual 88B.18 Line Out, Mic IN connector (CN55)B.19 Audio input from CD-ROM (CD IN; CN56)Table B.18: Ethernet 10/100Base-T RJ-45 por

89 Appendix B B.20 Aux Line-In connector (AUX IN; CN57)B.21 Front Panel audio connector (FP AUDIO; CN59)Table B.20: Aux Line-In connector (AUX IN;

AIMB-744 User’s Manual 90B.22 Case Open Connector (CN64)B.23 8-pin Alarm Board Connector (CN62)Table B.22: Case Open Connector (CN64)Pin Signal1 CAS

91 Appendix B B.24 System I/O PortsTable B.24: System I/O portsAddr. range (Hex) Device000-01F DMA controller020-021 Interrupt controller 1, master0

AIMB-744 User’s Manual 92B.25 DMA Channel AssignmentsB.26 Interrupt AssignmentsTable B.25: DMA channel assignmentsChannel Function0 Available1 Avail

93 Appendix B B.27 1st MB Memory MapB.28 PCI Bus MapB.29 PCI-X bus mapTable B.27: 1st MB memory mapAddr. range (Hex) DeviceE0000h - FFFFFh BIOSCC0

AIMB-744 User’s Manual 94

xi3.11 Password Setting ... 483.12 Save & Exit Setup ...

AIMB-744 User’s Manual xiiB.8 External Keyboard Connector (CN12)... 93Table B.8:External keyboard connector (CN12) ...

xiiiTable B.29:1st MB memory map ... 104B.30 PCI Bus Map ...

AIMB-744 User’s Manual xiv

1CHAPTER1General Information

AIMB-744 User’s Manual 2Chapter 1 Hardware Configuration1.1 IntroductionAdvantech's AIMB-744 series industrial motherboard is designed based on

31.2 Features1. Standard ATX form factor with industrial features: AIMB-744 provides industrial features like long product life, reliable operation u

AIMB-744 User’s Manual 4drives or four enhanced IDE devices. Supports PIO mode 4 (16.67MB/s data transfer rate) and ATA 33/66/100 (33/66/100MB/s data

51.3.6 Industrial features• Watchdog timer: Can generate a system reset or IRQ11. The watch-dog timer is programmable, with each unit equal to one se

AIMB-744 User’s Manual iiCopyright NoticeThis document is copyrighted, 2004, by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reser

AIMB-744 User’s Manual 6Table 1.2: ConnectorsLabelFunctionCN1 Primary IDE connectorCN2 Secondary IDE connectorCN3 Floppy drive connectorCN4 Parallel p

7CN62 8-pin Alarm Board ConnectorCN64 Case OpenSA0 Serial ATA 0SA1 Serial ATA 1ATX1 ATX 12V Auxiliary power connector ATX2 ATX power connectorTable 1.

AIMB-744 User’s Manual 81.5 Board Layout: Jumper and Connector LocationsFigure 1.1: Jumper and Connector locationsFigure 1.2: I/O ConnectorsCN59PCI-X

91.6 AIMB-744 Block DiagramFigure 1.3: AIMB-744 Block DiagramI n t el 82875P2ATA 100po r t s2 SATA po rts4USBPortsProce ssorG-L AN1 :82547 G ID D R

AIMB-744 User’s Manual 101.7 Safety Precautions Warning! Always completely disconnect the power cord from your chassis whenever you work with the har

11This device complies with the requirements in part 15 of the FCC rules: Operation is subject to the fol-lowing two conditions:1.This device may not

AIMB-744 User’s Manual 121.8 Jumper SettingsThis section provides instructions on how to configure your motherboard by setting the jumpers. It also i

13problem. The J2 jumper settings control the outcome of what the com-puter will do in the event the watchdog timer is tripped.1.8.4 PCI-X 33/66Mhz se

AIMB-744 User’s Manual 141.8.5 PCI-X slots 3.3V/5V selection (J8)The AIMB-744 contains a PCI-X 3.3V/5V selection that provide the user to select the o

15The AIMB-744 does not support ECC (error checking and correction). Memory modules with 9 SDRAM chips/side support ECC; modules with 8 chips/side do

iii1.0.1 A Message to the Customer Advantech customer servicesEach and every Advantech product is buil

AIMB-744 User’s Manual 161.11 Cache MemorySince the second-level (L2) cache has been embedded into the Intel® socket 478 Pentium® 4/Celeron™ processo

17 Chapter 2 CHAPTER 2Connecting Peripherals

AIMB-744 User’s Manual 18Chapter 2 Connecting Peripherals2.1 IntroductionYou can access most of the connectors from the top of the board while it is

19 Chapter 2 Connect the second hard drive to the remaining connector (CN2 or CN1), in the same way as described above. The secondary IDE shares the

AIMB-744 User’s Manual 202.5 USB Ports (CN6; shared with CN32)The AIMB-744 provides up to four ports of USB (Universal Serial Bus) interface, which

21 Chapter 2 Different devices implement the RS-232 standard in different ways. If you are having problems with a serial device, be sure to check the

AIMB-744 User’s Manual 222.9 CPU Fan Connector (CN14)If fan is used, this connector supports cooling fans of 500mA (6W) or less.2.10 System FAN conn

23 Chapter 2 CN16 is a 5-pin connector for the power on LED. Refer to Appendix B for detailed information on the pin assignments. If a PS/2 or ATX po

AIMB-744 User’s Manual 242.11.6 SM Bus Connector (CN29)This connector is reserved for Advantech's SNMP-1000 HTTP/SNMP Remote System Manager. The

25 Chapter 2 The AIMB-744 is equipped with one or two high-performance 10/100/1000 Mbps Ethernet LANs. They are supported by all major network operat

AIMB-744 User’s Manual ivTable 1.1: AIMB-744 DDR memory compatibility table Memory_Compatibility_TestBrand Size Speed Type Memory Apacer 256MB DDR266

AIMB-744 User’s Manual 262.16 Aux Line-In connector (AUX IN; CN57)The connector is for audio device with Line-in connector.2.17 Front Panel audio co

27 Chapter 2 2.18 8-pin Alarm Board Connector (CN62)The 8-pin alarm board connector is for Advantech chassis with alarm board. 2.19 Case Open Conne

AIMB-744 User’s Manual 28which eases cabling to hard drives with thin and long cables. 2.21 Connecting to SNMP-1000 remote managerUse the 6-pin to 8-

29 Chapter 3 CHAPTER 3Award BIOS Setup

AIMB-744 User’s Manual 30Chapter 3 Award BIOS Setup3.1 IntroductionAward’s BIOS ROM has a built-in setup program that allows users to modify the bas

31 Chapter 3 3.2 Entering SetupTurn on the computer and press <Del> to allow you to enter the BIOS setup. 3.3 Standard CMOS SetupChoose the “

AIMB-744 User’s Manual 323.4 Advanced BIOS FeaturesThe “Advanced BIOS Features” screen appears when choosing the “Advanced BIOS Features” item from

33 Chapter 3 3.4.5 Quick Power On Self TestAllows the system to skip certain tests while booting. This will decrease the time needed to boot the syst

AIMB-744 User’s Manual 343.4.15 Security OptionSelect whether the password is required every time the system boots or only when you enter setup."

35 Chapter 3 3.5.1 DRAM Timing SelectableThis item allows you to control the DRAM speed. The selections are "Manual" or "By SPD".

v1.0.2 Product warranty Advantech warrants to you, the original purchaser, that eac

AIMB-744 User’s Manual 363.5.7 System BIOS CacheableSelecting Enabled allows caching of the system BIOS ROM at F0000h-FFFFFh, resulting in better syst

37 Chapter 3 3.6 Integrated PeripheralsFigure 3.5: Integrated peripheralsFigure 3.6: On-Chip IDE Device

AIMB-744 User’s Manual 383.6.1 IDE HDD Block ModeIf your IDE hard drive supports block mode select Enabled for automatic detection of the optimal numb

39 Chapter 3 3.6.5 USB ControllerSelect Enabled if your system contains a Universal Serial Bus (USB) con-troller and you have USB peripherals. The ch

AIMB-744 User’s Manual 403.6.12 Onboard FDC ControllerWhen enabled, this field allows you to connect your floppy disk drives to the onboard floppy dis

41 Chapter 3 This field allows you to select EPP port type 1.7 or 1.9. The choices:"EPP1.9", "EPP1.7".3.6.22 ECP Mode Use DMAThis

AIMB-744 User’s Manual 42The Choice : "S1(POS)", and "S3(STR)". While selecting "S3(STR)", the "Run VGABIOS if S3 R

43 Chapter 3 This field allows you to select the CPU THRM-Throttling rate. The choices: "75.0%", "50.0%", and "25.0%".3

AIMB-744 User’s Manual 443.8.1 Reset Configuration DataDefault is Disable. Select Enable to reset Extended System Configuration Data (ESCD) if you hav

45 Chapter 3 3.9.4 Current CPUFAN SpeedThis shows you the current CPUFAN operating speed. 3.9.5 VCORE, +1.5V, VCC3, +5V, +12V, -12V, -5V, VBAT(V), 5V

AIMB-744 User’s Manual viStep 4. Carefully pack the defective product, a fully-completed Repair and Replacement Order Card and a photocopy proof of p

AIMB-744 User’s Manual 46Press <Enter>.2. If the CMOS is good or if this option has been used to change the default password, the user is asked

47 Chapter 4 CHAPTER 4Chipset Software Installation Utility

AIMB-744 User’s Manual 48Chapter 4 Chipset Software Install Utility4.1 Before you beginTo facilitate the installation of the enhanced display device

49 Chapter 4 • Identification of Intel ® chipset components in the Device Manager.• Integrates superior video features. These include filtered sealin

AIMB-744 User’s Manual 502. Click "Next" when you see the following message.3. Click "Yes" when you see the following message.

51 Chapter 4 4. Click "Next" when you see the following message.5. When the following message appears, click "Finish" to complete

AIMB-744 User’s Manual 52

53 Chapter 5 CHAPTER 5LAN Configuration

AIMB-744 User’s Manual 54Chapter 5 LAN Configuration5.1 IntroductionThe AIMB-744 features the 32-bit 10/100/1000 Mbps Ethernet network interface. Th

55 Chapter 5 5.3 InstallationThe AIMB-744's onboard Ethernet interface supports all major network operating systems. However, the installation

viiContentsChapter 1 Hardware Configuration ...21.1 Introduction ...

AIMB-744 User’s Manual 562. Select "I accept the terms in the license agreement" and click "Next" to continue.3. Click "Next

57 Chapter 5 4. Click "Install Software" to start the installation procedure.5. The driver will be installed automatically and the LAN func

AIMB-744 User’s Manual 58

59 Chapter 6 CHAPTER 6Onboard Security Setup

AIMB-744 User’s Manual 60Chapter 6 Onboard Security Setup6.1 IntroductionThe AIMB-744's hardware monitor is designed with Winbond W83782D. Onbo

61 Chapter 6 6.2 Windows XP Driver Setup1. Insert the driver CD into your system's CD-ROM drive. In a few seconds, the software installation ma

AIMB-744 User’s Manual 623. Click "Next" when you see the following message.4. Click "Next" when you see the following message.

63 Chapter 6 5. Click "Next" to continue.6. Click "Finish" when you see the following message.

AIMB-744 User’s Manual 646.3 Using the OBS Hardware Doctor UtilityAfter completing the setup, all the OBS functions are permanently enabled. When a m

65 Chapter 6

AIMB-744 User’s Manual viii2.5 USB Ports (CN6/CN63)... 202.6 VGA Connector (CN7) ...

AIMB-744 User’s Manual 66

67 Appendix A AppendixAProgramming the Watchdog Timer

AIMB-744 User’s Manual 68Appendix A Programming the watchdog timerA.1 Programming the Watchdog TimerThe AIMB-744's watchdog timer can be used

69 Appendix A Unlock W83627HSelect register of watchdog timerEnable the function ofthe watchdog timerUse the function of the watchdog timerLock W8362

AIMB-744 User’s Manual 70Watchdog Timer RegistersAddress of register (2E) AttributeRead/Write Value (2F) and description87 (hex) ----- Write this addr

71 Appendix A Table A.1: Watchdog timer registersA.1.4 Example Program1. Enable watchdog timer and set 10 sec. as timeout interval;------------------

AIMB-744 User’s Manual 72;-----------------------------------------------------------Dec dx ; Set second as counting unit Mov al,0f5hOut dx,alInc dxIn

73 Appendix A ;-----------------------------------------------------------Dec dx ; Enable the function of watchdog timerMov al,30hOut

AIMB-744 User’s Manual 74Out dx,al ;-----------------------------------------------------------Mov al,07h ; Select registers of

75 Appendix A Out dx,al ;-----------------------------------------------------------Mov al,07h ; Select registers of watchdog

ix3.4.8 Swap Floppy Drive ... 353.4.9 Boot UP Floppy Seek ...

AIMB-744 User’s Manual 76Out dx,al ;-----------------------------------------------------------Mov al,07h ; Select registers of

77 Appendix B AppendixBI/O Pin Assignments

AIMB-744 User’s Manual 78Appendix B Pin AssignmentsB.1 IDE Hard Drive Connector (CN1, CN2)Table B.1: IDE hard drive connector (CN1, CN2)Pin Signal

79 Appendix B B.2 Floppy Drive Connector (CN3)Table B.2: Floppy drive connector (CN3)Pin Signal Pin Signal1 GND 2 FDHDIN*3GND4N/C5 N/C 6 FDEDIN*7 GN

AIMB-744 User’s Manual 80B.3 Parallel Port Connector (CN4)Table B.3: Parallel port connector (CN4)Pin Signal Pin Signal1 STROBE* 14 AUTOFD*2D015ERR3D

81 Appendix B B.4 USB Connector (CN6; shared with CN32)B.5 COM1/2/3/4 RS-232 Serial Port Interface (CN9/10/23/38)Table B.4: USB1/USB2 connector

AIMB-744 User’s Manual 82B.6 Keyboard and Mouse Connnector (CN11)B.7 COM3/4 serial port connector ( CN10/23)9RI Table B.6: Keyboard and mouse connec

83 Appendix B B.8 External Keyboard Connector (CN12)B.9 CPU/System Fan Power Conn (CN14/15/37)8RI9GNDTable B.8: External keyboard connector (CN12)P

AIMB-744 User’s Manual 84B.10 Power LED (CN16)You can use an LED to indicate when the motherboard is on. Pin 1 of CN16 supplies the LED's power,

85 Appendix B B.12 Reset Connector (CN18)B.13 HDD LED Connector (CN19)Table B.12: Reset connector (CN18)Pin Signal1 RESET2GNDTable B.13: HDD LED co